And i dont understand how older i need the kernel .
Can you help me to choose the version to download and install? With the mini image of this post, linux freeze at boot, with 10.04 from your older post, problems with built in remote, and i have not tested with Ubuntu 9.10 – karmic .

Thanks!

xbmc@xbmc:~$ uname -a
Linux xbmc 2.6.32-30-generic #59-Ubuntu SMP Tue Mar 1 21:30:21 UTC 2011 i686 GNU/Linux

Thats perfect for me

xbmc@mikiXbmc:~$ cat /proc/bus/input/devices
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name=”Power Button”
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: EV=3
B: KEY=100000 0 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name=”Power Button”
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: EV=3
B: KEY=100000 0 0 0

I: Bus=0017 Vendor=0001 Product=0001 Version=0100
N: Name=”Macintosh mouse button emulation”
P: Phys=
S: Sysfs=/devices/virtual/input/input2
U: Uniq=
H: Handlers=mouse0 event2
B: EV=7
B: KEY=70000 0 0 0 0 0 0 0 0
B: REL=3

I: Bus=0003 Vendor=0a91 Product=3801 Version=0110
N: Name=”Wireless INC TW Wireless USB Device”
P: Phys=usb-0000:00:06.1-3.2/input0
S: Sysfs=/devices/pci0000:00/0000:00:06.1/usb2/2-3/2-3.2/2-3.2:1.0/input/input3
U: Uniq=
H: Handlers=kbd event3
B: EV=120013
B: KEY=10000 7 ff9f207a c14057ff febeffdf ffefffff ffffffff fffffffe
B: MSC=10
B: LED=1f

I: Bus=0003 Vendor=0a91 Product=3801 Version=0110
N: Name=”Wireless INC TW Wireless USB Device”
P: Phys=usb-0000:00:06.1-3.2/input1
S: Sysfs=/devices/pci0000:00/0000:00:06.1/usb2/2-3/2-3.2/2-3.2:1.1/input/input4
U: Uniq=
H: Handlers=kbd mouse1 event4
B: EV=1f
B: KEY=837fff 2c3027 bf004444 0 0 70001 c04 a27c000 267bfa d941dfed 9e0000 0 0 0
B: REL=147
B: ABS=1 0
B: MSC=10

I: Bus=0001 Vendor=10ec Product=0662 Version=0001
N: Name=”HDA Digital PCBeep”
P: Phys=card0/codec#0/beep0
S: Sysfs=/devices/pci0000:00/0000:00:08.0/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=40001
B: SND=6

xbmc@mikiXbmc:~$

verify you can see the device:

I: Bus=0003 Vendor=0471 Product=206c Version=0100
N: Name=”PHILIPS MCE USB IR Receiver- Spinel plusf0r ASUS”
P: Phys=usb-0000:00:04.0-1/input0
S: Sysfs=/devices/pci0000:00/0000:00:04.0/usb3/3-1/3-1:1.0/input/input3
U: Uniq=
H: Handlers=kbd mouse1 event3
B: EV=120017
B: KEY=c0000 400 0 0 70000 0 58000 8001f8 4000c004 e0beffdf 1cfffff ffffffff fffffffe
B: REL=103
B: MSC=10
B: LED=1f

First, thanks a lot for doing a good job with this instalations steps. Its very useful.
I have problems with remote, build in version.
Trying irw not shows anything.
I have done the old and this tutorials, but the same result with ir ..
Hardware.conf and lircd.conf seems ok.
Perhaps you can help me?

No I do not see anything like that, I download over 10GB rars in SAB, but I will verify my setup and check it out for you when I get home.

“Cannot open assembly ‘EmberSetup.exe’: File does not contain a valid CIL image.” when i run mono EmberSetup.exe

any advice?